Reznor R6GI Unit Installation Manual Manual do Utilizador descarregar pdf (Página 10)

Figure 5

Figure 4

• Electrical connections must be in compliance with

all applicable local codes and ordinances, and with

the current revision of the National Electric Code

(ANSI/NFPA 70).

• For Canadian installations the electricalconnections

and grounding shall comply with the current Canadian

Electrical Code (CSA C22.1 and/or local codes).

IMPORTANT NOTE:

Ifreplacinganyoftheoriginalwiressuppliedwiththe

furnace,thereplacementwiremustbecopperwiring

having the same guage, voltage, and temperature

rating.

Figure 5. Condensate Drain & Service Ports

ACCESSORY

ROOF CURB

Figure 4. RoofTopInstallation

Condensate

Drain

High Pressure

Low Pressure

AVERTISSEMENT:

RISQUEDECHOCÉLECTRIQUE,

D’INCENDIE OU D’EXPLOSION

Le non-respect des avertissements de sécurité

pourrait entraîner

unfonctionnementdangereux

de l’appareil,

des blessures graves, la mort ou

des dommages matériels.

Un entretein incorrect pourrait entraîner un

fonctionnementdangereuxdel’appareil,des

blessures graves, la mort ou des dommages

matériels

• Couper toute alimentation électrique au

générateur d’air chaud avant de prodéder

auxtravauxd’entretein.

• Aumomentdel’entretiendescommandes,

étiquetez tous les fils avant de les

débrancher. S’assurer de les raccorder

correctement.

•S’assurer que l’appareil fonctionne

adéquatement aprés l’entretien.

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failuretofollowsafetywarningsexactlycould

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Beforeservicing,disconnectallelectrical

powertofurnace.

• When servicing controls, label all wires

prior to disconnecting. Reconnect wires

correctly.

• Verifyproperoperationafterservicing.

ELECTRICAL WIRINGHorizontal to Downﬂow Conversion

The unit is shipped ready for horizontal duct connections.

If down ﬂow ducts are required, the unit must be converted

following the steps below for both the supply and return

ducts.

1. Remove both horizontal duct caps.

2. Locate the duct cap inside the duct openings and remove

the screw holding it in place.

3. Lift the cap out of the unit. (Hint: The cap can be pushed

up from the bottom by reaching through the fork slot).

4. Cover the horizontal duct openings with the horizontal

duct caps removed earlier in step 1. The insulation will

be on the indoor side.

5. Fasten the cover with screws to seal.

6. Remove and discard the two wood supports beneath

the unit.

Condensate Drain

Condensate is removed from the unit through the 3/4”

female pipe ﬁtting (Figure 5) located on the front side of

the unit. Install a 2 inch condensate trap in the drain line of

the same size and prime with water. When connecting rigid

drain line, hold the female ﬁtting with a wrench to prevent

twisting. Do not over tighten! Refer to local codes and

restrictions for proper condensate disposal requirements.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 39 40

Comentários a estes Manuais

Sem comentários

Reznor R6GI Unit Installation Manual Manual do Utilizador Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Radiadores Reznor R6GI Unit Installation Manual